PIC16F737-I/SP【PDF 70/231 页】IC PIC MCU FLASH 4KX14 28DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3841

66页 67页 68页 69页 [70页]71页 72页 73页 74页

2009 Microchip Technology Inc.

DS39636D-page 167

PIC18F2X1X/4X1X

16.4.3.2

Reception

When the R/W bit of the address byte is clear and an

address match occurs, the R/W bit of the SSPSTAT

the SSPBUF register and the SDA line is held low

(ACK).

When the address byte overflow condition exists, then

the no Acknowledge (ACK) pulse is given. An overflow

condition is defined as either bit BF (SSPSTAT<0>) is

set, or bit SSPOV (SSPCON1<6>) is set.

An MSSP interrupt is generated for each data transfer

byte. Flag bit, SSPIF (PIR1<3>), must be cleared in

software. The SSPSTAT register is used to determine

the status of the byte.

If SEN is enabled (SSPCON2<0> = 1), RC3/SCK/SCL

will be held low (clock stretch) following each data

transfer. The clock must be released by setting bit CKP

(SSPCON<4>). See Section 16.4.4 “Clock Stretching”

for more detail.

16.4.3.3

Transmission

When the R/W bit of the incoming address byte is set

and an address match occurs, the R/W bit of the

SSPSTAT register is set. The received address is

loaded into the SSPBUF register. The ACK pulse will

be sent on the ninth bit and pin RC3/SCK/SCL is held

low regardless of SEN (see Section 16.4.4 “Clock

Stretching” for more detail). By stretching the clock,

the master will be unable to assert another clock pulse

until the slave is done preparing the transmit data. The

transmit data must be loaded into the SSPBUF register

which also loads the SSPSR register. Then pin RC3/

SCK/SCL should be enabled by setting bit CKP

(SSPCON1<4>). The eight data bits are shifted out on

the falling edge of the SCL input. This ensures that the

SDA signal is valid during the SCL high time

(Figure 16-9).

The ACK pulse from the master-receiver is latched on

the rising edge of the ninth SCL input pulse. If the SDA

line is high (not ACK), then the data transfer is com-

plete. In this case, when the ACK is latched by the

slave, the slave logic is reset (resets SSPSTAT regis-

ter) and the slave monitors for another occurrence of

the Start bit. If the SDA line was low (ACK), the next

transmit data must be loaded into the SSPBUF register.

Again, pin RC3/SCK/SCL must be enabled by setting

bit CKP.

An MSSP interrupt is generated for each data transfer

byte. The SSPIF bit must be cleared in software and

the SSPSTAT register is used to determine the status

of the byte. The SSPIF bit is set on the falling edge of

the ninth clock pulse.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式